||USB to I2C Host Adapter
with ASCII Fast Mode Interface
iPort/USB brings I2C directly to your Windows PC. Just load our free software, plug the iPort/USB into your computer's USB port, and you will be sending and receiving I2C messages in seconds.
Over the past few years, the I2C Bus has expanded from simple control to data intensive applications. As new uses arise, bus bandwidth and message overhead have become key issues in product design and testing. The iPort/USB, our fourth generation adapter for the I2C Bus, addresses these issues by supporting several I2C bus speeds, including fast mode (400kbit/s), and USB transfer rates up to 12 Mb/s. Implemented using a high-performance bus co-processor with optimized instruction set, the adapter also includes large message buffers (256 bytes) to reduce host computer and bus overhead. In addition to operating as a bus master or slave in a multi-master system, a built-in bi-directional /INT signal line allows the device to receive or generate "slave only" device notifications.
Thanks to its USB-based Virtual Communications Port (VCP) driver, the iPort/USB will work with RS-232 based applications written for our iPort/AFM or iPort/AI I2C host adapters. When operating with new application software that uses advanced features, speed increases up to 100X faster are possible.
Master and Slave, Transmit and Receive, iPort/USB supports I2C message modes including Multi-Master, Arbitration Loss Detection, withÝ messages from 1 to 32K bytes in length.
Start sending I2C messages in minutes using our Message Manager or Message Center applications included with each adapter. You can also use your computer's terminal emulation software (like Windows' Hyperterminal Program), or create your own custom I2C applications using any programming tool that can access your computer's (virtual) serial port.
ASCII Text Interface Commands
|Note: [CR] = Carriage
Return Code or Enter Key.
Syntax: [Select], (Optional), xx = [00..FE], n = [1..32767]
This command resets the iPort/USB to its default state.
Display iPort/USB status information.
|/B[0|1|2][CR]||Virtual Com Port Baud Rate Control
Set the Virtual Com Port Baud Rate (0=19.2, 1=57.6, 2=115.2k)
|/C[CR]||Close I2C Connection
Disconnect from the I2C Bus.
|/Dxx[CR]||Set Destination I2C Slave Address
Set the destination I2C Slave Address for subsequent Master Transmit or Receive operations.
|/E[0|1][CR]||Echo/Prompt Control [0 = Disable, 1
Enable/Disable data entry echo and prompts.
|/F[0|1][CR]||Virtual Com Port Flow Control [0 = XON/XOFF,
1 = RTS/CTS]
Select serial communication handshaking protocol.
|/G[0|1][CR]||I2C General Call Control [0 = Disabled,
1 = Enabled]
Enables/Disables iPort/USB response to I2C Bus General Call (00) messages.
|/H[0|1][CR]||Hex Only Display Control [0 = Disabled,
1 = Enabled]
Controls display format of received message data.
|/Ixx[CR]||Set iPort/USB s Own I2C Slave Address
Sets iPort/USB's own I2C Slave Address. iPort/USB will respond to I2C Bus messages sent to this address.
|/K[0|1|2|3][CR]||I2C Bus Clock Rate Control
Set I2C Bus Clock Rate ControlÝ (0=23, 1=86, 2=100, 3=400 KHz)
|/M[CR]||Command Menu Display
Display iPort/USB's Command Menu
|/N[0|1|A|R][CR]||iNterrupt Signal Monitor/Control Status
Sets Monitor/Control/Status /INT Line. [0=Disable, 1=Enable, A=Assert, R=Release, [CR] = Status]
|/O[CR]||Open I2C Connection
Activates iPort/USB as an I2C device attached to the bus.
|/*Rn[CR]||Master Read Message
Read the specified number of data bytes from the current Destination I2C Slave device. * = No Stop for Repeated Start
|/Stext[CR]||Slave Transmit Message
Write the specified data bytes to a requesting I2C Master Receiver device.
|/*Ttext[CR]||Master Transmit Message
Master Transmit the specified data bytes to the current Destination I2C Slave device. * = No Stop for Repeated StartÝ
|/Un[CR]||I2C Bus Time-oUt
Set the I2C Bus Time-oUt in msec (0=Disable)
(Major XX.XX Minor)
Direct control of I2C Clock (SCL) and Data (SDA) lines. See User's Guide for details.
|/Y[CR]||Display Tx bYte
How many bytes did slave acknowledge.
Included Parts List
Optional Add-On Parts
Product Environmental Specifications: See Environmental Specifications FAQ
See our Online Catalog for ordering information.
I2C is just a mouse click away TM
| MCC | | iPort | | iPort/AI | | iPort/AFM | | iPort/USB | | Bus Monitor | | Bus Monitor Plus |
| I2C Bus Ovr. | | LabVIEW | | Sample Prog. | | User's Guides | | FAQ | | iPort FAQ |
Page up-dated at June 04, 2007